Understanding Essential Plumbing Skills is Crucial for Installing a Bathtub
Understanding Essential Plumbing Skills is Crucial for Installing a Bathtub
Blog Article
What are your opinions concerning A Step-by-Step Guide to Installing a Bathtub?
Mounting a bath tub isn't specifically brain surgery, but it does require solid plumbing, woodworking, and also often, tiling abilities. Replacing an old bathtub with a new one is additionally a moderately hard job. If the old tub is easily available, the job can move quickly; if you need to open up a wall to eliminate the old tub and also place the new bathtub, the job is much harder. In either case, the task is within a residence handyman's abilities, although you will need a helper to move out the old tub and embeded in the new one. See to it you have certified on your own for the work and are comfortable attempting it. As opposed to working with a specialist to take control of a halfway-completed project, it is better to think about using one prior to you start. Opportunities are you might require an expert plumber to make tube connections.
This short article will help you install a new bath tub in your washroom if you have actually already purchased a new bathtub as well as do not need to alter the arrangement of your previous water pipelines.
Your devices as well as product list ought to comprise the following:
Planning for the Setup
To start with, the supporting frame provided with the bath should be fitted (if required) according to the producer's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make sure that if the tap includes a plastic washing machine, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets unit to prevent stress on the bathtub.
Fit the adaptable faucet connectors to the bottom of both taps utilizing 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bathroom. Utilize the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you use every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now prepare to be suited its last position.
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water supply. After doing so, turn on the taps to drain any water continuing to be in the system. The procedure of removing the existing taps can be fairly troublesome because of the restricted gain access to that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric all set for the staying water that will originate from the pipes. Once the supply pipes have actually been removed, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary taps from transforming throughout this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any old sealing compound.
Prior to moving on to fit the new faucets, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Setting up the Tub
Using the two wooden boards under its feet, put the tub in the needed setting. The wood boards are helpful in evenly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to ensure that the bath tub is leveled all round. This can be attained by examining the level and adjusting the feet on the bathtub till the level checks out degree.
To mount taps, fit all-time low of the outermost versatile tap connector to the ideal supply pipeline by making a compression join; then do the very same for the other faucet.
Turn on the supply of water and examine all joints and brand-new pipework for leaks as well as tighten them if necessary. Load the tub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the bathtub must wait up until the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a connection to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the installing hole in the bath/basin making certain that the washers are in area between the faucet as well as the sink. Secure the tap in position with the producer provided backnut. When the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical tap adapters. The former type must be attached to the faucet ends first, tightening just by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to break an inflexible seal, creating the water to pass through the wall between the bathroom and the tiling, bring about problems with dampness as well as feasible leakages to the ceiling listed below.
You can pick from a variety of coloured sealants to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, and can sealing voids approximately a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with twists of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to enable the activity experienced when the bathtub is in usage. The sealant can crack fairly very early if you do not consider this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently readily available on the market. It is a good idea to fit the ceramic tiles utilizing water-resistant or water-proof glue as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you enjoy reading about How to Install a Bathtub Yourself? Leave a remark directly below. We would be glad to know your ideas about this review. In hopes that you come back again soon. Sharing is nice. Helping people is fun. Bless you for your time. Come back soon.
Dial, we deliver! Report this page